ragged curves on pseudosection

Topics that do not fit into the other categories
Post Reply
User avatar
js
Posts: 13
Joined: 21 Nov 2015, 16:04

ragged curves on pseudosection

Post by js »

Hi everyone,

I'm calculating pseudosection using td-tcds62-6axmn-03.txt dataset. Unfortunately, calculated pseudosection looks very strange (see below). Does anyone know what is the problem?

Jacek Sz.

361-1.png
361-1.png (99.51 KiB) Viewed 30574 times
User avatar
alex
Posts: 1
Joined: 07 Nov 2018, 19:30

Re: ragged curves on pseudosection

Post by alex »

Hello, 

Local minima related to the LiQ model? Plus labels :) 

It is a common proble for me with amphibole / cpx at HP/LT. I would try without the melt model. 

Alex  
User avatar
js
Posts: 13
Joined: 21 Nov 2015, 16:04

Re: ragged curves on pseudosection

Post by js »

Hi Alex,

thanks for your advice. I'll try to do this. However, this problem doesn’t exist using different dataset.

Jacek
User avatar
pierre.lanari
Posts: 10
Joined: 29 Oct 2015, 11:45

Re: ragged curves on pseudosection

Post by pierre.lanari »

Hi Jacek, How did you define the number of oxygen in your bulk? I you are using O(?), I suggest you to add a little extra oxygen to avoid minimization issues with the ferric end-members. I would try to calculate the diagram between 550-600 °C and 5000-7500 bar using the following bulk:
1    SI(66.84)AL(16.44)FE(3.14)MG(3.24)CA(0.55)NA(6.56)K(2.77)TI(0.43)MN(0.05)O(?)O(0.001)    *
Another thing you could do is to run manually a few minimizations with Theriak in this P-T range and try to figure out what the problem actually is. Pierre 
User avatar
js
Posts: 13
Joined: 21 Nov 2015, 16:04

Re: ragged curves on pseudosection

Post by js »

Hi Pierre,thanks for your replay. I'm using the following bulk:

1   SI(66.8367)AL(16.4382)FE(3.1427)MG(3.2363)MN(0.0488)CA(0.5455)NA(6.5557)K(2.7697)TI(0.4264)H(100)O(?)  * 

So, if I understand you I could modify this bulk to:

1   SI(66.8367)AL(16.4382)FE(3.1427)MG(3.2363)MN(0.0488)CA(0.5455)NA(6.5557)K(2.7697)TI(0.4264)H(100)O(?)O(0.001)  * 

Am I right?
Jacek 
User avatar
tyler
Posts: 2
Joined: 25 Nov 2018, 23:21

Re: ragged curves on pseudosection

Post by tyler »

Hi Jacek,

Doug Tinkham discusses the issue with Ferric iron on his site (http://dtinkham.net/peq.html) under the section Ferric Iron Problems.

And yes, I believe that Pierre is correct in added a minor amount of  O to your bulk.
Tyler AmbrosePostdoctoral Fellow
User avatar
Salviano Silva
Posts: 1
Joined: 18 Nov 2019, 17:03

Re: ragged curves on pseudosection

Post by Salviano Silva »

Hi everyone,

I have a similar problem to the Jacek, however even adding a little extra oxygen the results are still odd.

To the calculation, I am using the tcdb55c2d.txt dataset.
Does anyone know what is the problem?

Salviano

361-7_sm.png
361-7_sm.png (294.96 KiB) Viewed 30572 times
Post Reply